Free Vibration of Fixed Fixed Beam

Free Vibration of Fixed Fixed Beam - Theory

Learning Objectives

After completing this remote triggered experiment on free vibration of a fixed fixed beam one should be able to

  • Model a given real system to an equivalent simplified model of a fixed fixed beam with suitable assumptions / idealizations.
  • Calculate the logarithmic decrement, damping ratio, damping frequency and natural frequency of the system
  • Find the stiffness and the critical damping of the system.
  • Calculate damping coefficient of the system.

Introduction

A system is said to be a Fixed-Fixed beam system if it has a fixed connections at both its ends.

Vibration analysis of a fixed-fixed beam system is important as it can explain and help us analyse a number of real life systems. The following few real system can be simplified to a fixed-fixed beam, thereby helping us make design changes accordingly for the most efficient systems.

Following few figures tell us about the significance of analysing Fixed-Fixed beams and their relevance to the real world.

                                                               

Suspension System                                                                          Pillow Lock Joint

The above figure depicts a fixed-fixed suspension system and the pillow lock joint at its ends. In machinery too, we can find parts which can be analysed as fixed-fixed beams like in the following grinder and the support system to a furnace.

                                              

        Grinding Machine                                                                        Furnace Supporting Structure

Natural Frequency of Fixed Fixed Beam

When given an excitation and left to vibrate on its own, the frequency at which a fixed fixed beam will oscillate is its natural frequency. This condition is called Free vibration. The value of natural frequency depends only on system parameters of mass and stiffness. When a real system is approximated to a fixed fixed beam, some assumptions are made for modelling and analysis (Important assumptions for undamped system are given below):

  • The mass ($m$) of the whole system is considered to be lumped at the middle of the beam
  • No energy consuming element (damping) is present in the system i.e. undamped vibration
  • The complex cross section and type of material of the real system has been simplified to equate to a fixed fixed beam

The governing equation for such a system (spring mass system without damping under free vibration) is as below: $$ m\ddot{x}+kx= 0 $$$$ \ddot{x}+ω_n^2 x=0 $$ $$\omega_n = \sqrt{\frac k m} $$ $k$ , the stiffness of the system is a property which depends on the length ($l$), moment of inertia ($I$) and Young's Modulus ($E$) of the material of the beam and for a fixed fixed beam is given by: $$k=\frac{192EI}{l^3}$$

Damping in a Fixed Fixed Beam

Although there is no visible damper (dashpot) the real system has some amount of damping present in it. When a system with damping undergoes free vibration the damping property must also be considered for the modelling and analysis.

Single degree of freedom mass spring damper system under free vibration is governed by the following differential equation: $$ m\ddot{x}+c\dot{x}+kx= 0 $$ $$ \ddot{x}+2\zeta\omega_n\dot{x}+\omega_n^2 x=0 $$ $c$ is the damping present in the system and $\zeta$ is the damping factor of the system which is nothing but ratio of damping $c$ and critical damping $c_c$. Critical damping can be seen as the damping just sufficient to avoid oscillations. At critical condition $\zeta =1$. For real systems the value of $\zeta$ is less than 1. For system where $ \zeta < 1 $ the differential equation solution is a pair of complex conjugates. The displacement solution is given by $$ x(t) = e^{- \zeta \omega_n t} \left[ x_0 cos (\omega_d t) + \frac {v_0 + \zeta \omega_n x_0} {\omega_d} sin (\omega_d t) \right] $$ where $x_0$ and $v_0$ are initial displacement and velocity and $\omega_d$ is the damped natural frequency of the system. The damped natural frequency is calculated as below: $$ \omega_d = \omega_n \sqrt {1- \zeta ^2} $$

Free Vibration of Fixed Fixed Beam - Procedure

AIM

  • Determine the damped natural frequency, logarithmic decrement and damping ratio of a given system from the free vibration response
  • Calculate the mass of the system actively participating in dynamics
  • Determine the equivalent viscous damping present in the system
  • Calculate critical damping of the system and undamped natural frequency of the system

GENERAL INSTRUCTIONS

WE INSIST THAT USER READ THE INSTRUCTIONS & PROCEDURE THOROUGHLY BEFORE CARRYING OUT THE EXPERIMENT.

ONLINE and OFFLINE modes :

For the user to conduct an experiment, he/she must be connected to the SOLVE lab servers at NITK Surathkal. For this the user must be in the ONLINE mode. The user will be allowed to save the results of the online experiments and use the same for further analysis in OFFLINE mode. In case of OFFLINE mode the user is not connected to the experiment. However he/she can load a previously saved data file to get required graphs and carry out further analysis of the data. For this to happen, the user MUST have a Saved Data of the same experiment. Refer to step 6 below in procedure for downloading data.

CONTROL and VIEW modes :

In ONLINE mode, depending on availability of experiment, a user may get CONTROL or VIEW mode. In CONTROL mode the user gets to control the experiment parameters and trigger the experiment. In VIEW mode the user will not be able to control the experiment or trigger it, but will receive the data acquired during the experiment. The graph will load on screen once the data acquisition is complete. The VIEW user can chose to continue to calculations with the data received. ONLY ONE user is allowed to be in the CONTROL mode at any instant.

Allowed Actions during Remote Trigger :

While doing the experiment, i.e. when user is in Remote Trigger window, right click is permitted only in the graph area where the context menu will give options to zoom in, zoom out, save as image etc. Also, user MUST NOT REFRESH the page while carrying out an experiment. Page refreshing leads to loss of connection with the experiment server. However, the users may move back and forth between PROCEDURE tab and REMOTE TRIGGER tab while doing calculations, if they need to refer to formula given in table below.

Note: Time remaining and Number of Trials left are shown in INDICATOR block. If time is up or the number of trials left is zero the user automatically gets disconnected from the experiment server.

FORMULA

Effective mass of fixed fixed beam concentrated at the mid point is 0.375mbeam. So for this experiment m=msensor+0.375mbeam

PROCEDURE:

Fig 1: (a) Schematic of the experimental setup; (b) Equivalent engineering model; (c) Lumped parameter system

1. To conduct experiment click Start. In order to load previously saved data click on Choose file and locate the appropriate file. A pop-up dialogue box will inform you on successful loading of data. You can access the graphs and proceed to calculations once you click OK on the pop-up box. (Go to step 4 for calculations)

2. Once you are connected to the experiment server in CONTROL mode you can carry out the experiment. Depending upon the availability you will be granted CONTROL or VIEW mode. If you are granted VIEW mode you will be put in Queue and will be shown the waiting time for getting a CONTROL slot. You can either wait or you can chose to use the data acquired during ongoing session to proceed to calculations (Step 4)

 

3. Click on Trigger to actuate electromagnet. The electromagnet will attract and leave the free end of the fixed fixed beam due to which the fixed fixed beam will be set into free vibration. The acceleration data from accelerometer will load shortly on to your screen. Once you have received the data you may either choose to TRIGGER AGAIN or Disconnect from the experiment server. Number of trials left and the time left for you to finish the experiment are shown in Indicators block.

4. Click Proceed to Calculations to move to the calculations window. Known parameters are listed below the graphs. Hover over a point on the graph to find its x and y coordinates. Use available values to calculate listed parameters and enter them in appropriate fields. During calculations, the user may refer to table of formula given under the heading FORMULA above.

5. Click on Submit Calculations and View Results to submit your data. ONCE SUBMITTED ANSWERS CAN NOT BE REVERTED. A pop-up box will ask for your confirmation to submit the result. Click OK to CONTINUE. Click CANCEL if you wish to CHECK your data.

6. Click on Download Data button below the graph to download and save your data. You can use this file to load the graph and continue to calculations in the OFFLINE mode. You may also save your results (for your record) by clicking Download Results . You will receive a CSV file containing the data of your results table.

Questions:3
Attempts allowed:Unlimited
Available:Always
Pass rate:75 %
Backwards navigation:Allowed

Free Vibration of Fixed Fixed Beam - Assignment

Try the following

  • Plot the variation of natural frequency of fixed fixed beam with
    1. Length of Beam
    2. Lumped mass at center of the beam
  • What is the time taken to reduce vibration amplitude to half its initial value? How does it vary with damping ratio?
  • Mechanical Vibrations by "Singiresu S. Rao", Addison-Wesley Longman Incorporated, 1990
     
  • Theory of Vibrations with Applications by "Chandramouli Padmanabhan, Marie Dillon Dahleh, William T. Thomson", Pearson Education, 2008
     
  • Mechanical Vibration Practice and Noise Control by "V. Ramamurthi", Narosa Publishing House, 2012
     
  • Mechanical Vibration by "Haym Benaroya and Mark L. Nagurka", CRC Press 2010
     
  • Vibration and Acoustics by "Sujatha C", McGraw Hill Education, 2010
     
  • Mechanical Vibrations by "G K Grover", NEM Chand & Bros, 2009
     
Questions:3
Attempts allowed:Unlimited
Available:Always
Pass rate:75 %
Backwards navigation:Allowed
 

Get in touch with us

Contact us

Center for System Design (CSD)

NITK, Surathkal.
P. O. Srinivasnagar,
Mangalore - 575025, Karnataka, India

Tel: +91-824-2473915
Email: csd@nitk.edu.in

Education - This is a contributing Drupal Theme
Design by WeebPal.